RM24948
Universal Remote
Instruction Manual
Button Functions
Code Entry using the Code List
Red Indicator
Lights when any
button is pressed.
1. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
POWER Turns
product On or Off.
SETUP Used to setup
the remote, and for
code search function.
2. Press and release the desired device
button (TV, VCR, etc.). The red indicator
blinks, then stays lit.
TV, CBL/AUX, VCR/DVD
Selects product to be
operated.
3. Enter the 4 digit code for
your brand of TV, VCR,
etc., from the Library Code
Table by using the Rewind,
Play, and Fast Forward
buttons.
CHANNEL Up/Down
Changes the channels.
Also controls DVD SKIP
functions.
MUTE Turns off the
TV sound, while the
picture remains.
Use the REW button to enter the first digit.
Use the Play button to enter second digit.
Use the FF button to enter the third digit.
VOLUME UP/DOWN
Changes the volume
level of the product,
normally the TV.
RECORD, PLAY, STOP,
REW, FF, PAUSE VCR/DVD
control buttons operate
your VCR or DVD even
when the remote is set to
operate the TV.
For Example: To enter code 013, don’t press REW,
press Play once, and FF three times. The red LED
blinks off with each keypress.
4. Press the Stop button to save the code.
Note: The REC button must be pressed TWICE to
record from your VCR. For some brands of VCRs, you
might need to press the REC button once, then press it
again for three seconds.
Note: for a valid code, the red LED turns off. For an
invalid code, the red LED blinks rapidly for three
seconds before going off.
5. With your device on, press POWER. If the
device turns off, no further programming is
required. Note: If some buttons do not operate
your equipment, try one of the other codes for
your brand.
4
5
Setting up using Code Search
UsingYour Remote
If you cannot find a 4 digit code in the Code Table
that operates your TV, try searching for the code as
follows:
Code Retrieval
Code Retrieval lets you identify the four digit library
code stored under your device button. For example,
if you want to find out what four digit code is stored
under your TV device button, follow the six steps
below:
1. Manually turn on the device (TV, VCR, etc.) to
be controlled.
2. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
1. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
3. Press and quickly release the desired
device button (TV, VCR, etc.). The red
indicator blinks off once.
2. Press and release the desired device
button (TV, VCR, etc.). The red
indicator blinks, then stays lit.
4. Press the POWER button
repeatedly (up to 300 times) until
the device to be controlled turns off.
The red indicator blinks off with each
button press.
3. Press and release the SETUP button.
The red indicator blinks once and
remains lit.
4. To find the first digit for the code stored
under the device button pressed in step
2, press REW and count the number of
blinks.
5. Press and release STOP to install the
code.
5. To find the second digit, press Play
and count the number of blinks.
Write your codes down here for easy reference
later.
6. To find the third digit, press FF and
count the number of blinks.
Device
Device stored Code
TV
TV
CBL/AUX
VCR/DVD
6
7
UsingYour Remote, cont.
UsingYour Remote, cont.
Controlling Devices with Separate Power
On and Off Buttons
Setting ALL Volume/Mute Control to any
one Mode
Some GE, RCA and ProScan models require you to
press the device button for more than one second
to turn the device on and the POWER button to turn
the device off.
This routine can set all Modes to “punch-through” to
any one chosen Mode for Volume/Mute button
control without the needing to change to that Mode.
1. Press and hold SETUP until the red
indicator turns on, then release SETUP.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up two
different Mode buttons to control both parts of the
Combo device. For example, if you have a TV/DVD
Combo, you might need to set up one code under
the TV button to control the TV part AND a
separate code (under any other Mode button) to
control the DVD part.
2. Press and hold MUTE until the red
indicator blinks off, then release MUTE.
3. Press and release the desired Mode
button (TV, VCR) for Volume/Mute control,
the red indicator blinks then stays on.
4. Press and release MUTE and the red
indicator turns off. The red indicator will
blink rapidly for three seconds if the Mode
you have selected has no Volume/Mute
control.
VCR/DVD Punch-Through
This remote allows the 6 VCR transport buttons
(i.e. PLAY, PAUSE, STOP, FF, REWIND, and REC)
to Punch-Through control from any Mode
programmed with TV, SAT or Cable codes to the
last VCR, or DVD programmed Mode you used.
This feature will not operate if the programmed TV,
SAT or Cable code has its own VCR transport
button control e.g. a TV Combo, SAT/PVR, etc.
All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
Returning Volume/Mute Control to Initial
Default Settings
This routine returns Volume/Mute control to its
default (factory) settings i.e. all device Modes
use their own Volume/Mute control if present or
else they will punch-through control to the TV
Mode device.
Volume/Mute Control and Punch-Through
This remote lets you select which device Mode
controls your Volume/Mute buttons. The remote is
initially set for all device Modes to use their own
Volume/Mute control if present. If the programmed
code has no Volume/Mute operation of its own then
those buttons will punch-through control to the TV
Mode device without needing to change to TV
Mode.
1. Press and hold SETUP until the red
indicator turns on, then release SETUP.
2. Press and hold MUTE until the red
indicator blinks off, then release MUTE.
3. Press and release MUTE and the red
indicator turns off. Volume/Mute control
is returned to its default (factory)
Any Mode chosen for Volume/Mute control
MUST have its own Volume/Mute function or
the Volume/Mute buttons will do nothing.
settings.
8
9
Troubleshooting
90 Day Limited Warranty
Remote does not operate your product.
Jasco Products Company warrants this product to
be free from manufacturing defects for a period of
ninety days from the original date of consumer
purchase. This warranty is limited to the repair or
replacement of this product only and does not
extend to consequential or incidental damage to
other products that may be used with this unit. This
warranty is in lieu of all other warranties express or
implied. Some states do not allow limitations on
how long an implied warranty lasts or permit the
exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to
you. This warranty gives you specific rights, and
you may also have other rights which vary from
state to state. If unit should prove defective within
the warranty period, return prepaid with dated proof
of purchase to:
•
Press the device button of the product you want
to control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to
reprogram your remote after installing new
batteries.)
•
Remote may not be compatible with your
product.
Remote does not operate some features of
your product.
•
•
Sometimes a particular code might operate
some features but not all. Try programing
remote with a new code.
Remote may not be able to operate all features
of your product or button names might be
different than your product.
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Red Indicator blinks after you program a
product code.
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
Lost Your Codes?
Enclosed with this remote is a sticker on which you
should write the codes for each device you
programmed. Apply the sticker to the back of the
remote or somewhere convenient for future
reference.
Also on the sticker is our website address which,
should you lose your codes or programming
instructions, you can find available on our website:
10
11
RM24948
Universal Remote
Instruction Manual
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Made in China
RM24948-03/05
|