Register your product and get support at
SWW1800/27
Quick Start Guide
Connect
1
Install
2
Enjoy
3
1
Connect
Transmitter
Receiver
HDMI OUT
DC IN 5V
DC 5V
2
1
HDMI OUT
Connect the transmitter to your HD devices
1
Connect video source to the transmitter using the HDMI cable
Connect one end of the HDMI cable (included) to the HDMI connector of the
transmitter.
•
2
Connect the video source to the transmitter using the component cables
Connect one end of the RCA (green, blue and red) cables to the Y/Pb/Pr IN
connectors of the transmitter. Connect the other end of the RCA cables to the
corresponding Y/Pb/Pr OUT connectors of your HD devices.
•
•
Connect one end of the set of audio cables to the AUDIO L/R IN connectors
of the transmitter. Connect the other end to the corresponding AUDIO L/R
OUT connectors of your HD devices.
3
Connect the power adaptor to the transmitter
Connect one end of the power adapter (included) to the DC IN connector
of the transmitter. Connect the other end of the power adaptor to a power
socket.
•
»
»
The power LED indicator lights up in solid red.
The HDMI devices and analog devices with the component and stereo RCA start connecting.
Connect the receiver to your HDTV set
1
•
Connect the receiver with an additional HDMI cable (not included):
Connect one end of the HDMI cable to the receiver.
•
Connect the other end to the HDMI OUT connector of your HDTV.
2
Connect the power adaptor to the receiver:
Connect one end of the power adapter (included) to the DC IN connector of
the receiver.
•
•
Connect the other end of the power adaptor to a power socket.
Install
2
Install remote control batteries
1
2
Open the battery compartment.
Insert two AAA batteries with correct
polarity (+/-) as indicated.
3
Close the battery compartment.
3
Enjoy
DC 5V
Turn on the power of your
HDTV
1
2
Go to the source menu under the settings menu of your HDTV.
Select the HDMI input to which the receiver is connected.
Note
• You cannot control the receiver with the supplied remote control and the
receiver follows the transmitter’s status to enter/exit the standby mode.
• The synchronization of standby between the HDTV and the receiver
depends on the capability of the HDTV.
Switch on the transmitter
Press on the remote control or transmitter in standby mode to turn it on.
Select the source on the transmitter
Press the source buttons: 1 HDMI , 2 HDMI, 3 INPUT, 4
INPUT on the remote control or transmitter until you
see the available video from your device.
Note
• In standby mode, a red power LED displays on the
transmitter .
• Depending on equipment and the input selected,
between input selection/start-up and being able
to see the image on your TV can take up to 15
seconds.
Wallmount the receiver
You can either place the receiver near the HDTV or mount
it on the wall.
1
2
Choose a spot near the TV.
Drill two holes in the wall. Ensure the distance
between the two holes is 4.5mm.
3
4
5
Punch the supplied plastic wall anchors into the two
holes on the wall.
Put the two screws into the plastic wall anchors and
leave 3.2mm to mount the receiver on.
Hook the receiver on the wall.
Troubleshooting
There is no video displayed on myTV screen.
•
Verify the POWER LED and SOURCE LED indicator on the transmitter:
I cannot hear any sound or the sound is poor, what do I do?
•
•
•
•
Ensure the TV volume control is adjusted correctly.
Ensure the TV volume is not set to minimum or the sound is not muted.
Ensure the audio cables of the transmitter are connected correctly.
Ensure the Audio format is recognized/supported.
Long switching time due to the channel switching on a satellite/cable set-top box.
•
Select video scaling if your set-top box supports this feature so as to keep the output
resolution constant.
Tip
•
For more information, see the user manual.
Welcome to Philips
Register your product at www.philips.com/welcome
Need help?
User Manual
Refer to the User Manual that came with your SWW1800.
Online help
© 2009 Koninklijke Philips Electronics N.V.All rights reserved. Reproduction in whole
or in part is prohibited without the written consent of the copyright owner.
Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners.
0682
Printed inTaiwan
SWW1800_27_EN_QSG_V1.1
|