Kandy
STEREO POWER
AMPLIFIER
U S E R M A N U A L
R O K S A N A U D I O L I M I T E D
6 NORTHFIELD INDUSTRIAL ESTATE
BERESFORD AVENUE
MIDDLESEX HA0 1NW
ALPERTON
ENGLAND
T E L .
F A X .
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 1
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 2
+ 4 4 ( 0 ) 2 0 8 9 0 0 0 7 3 4
w w w . r o k sa n . c o . u k
e ma i l in f o @ r o k s a n . c o . u k
CAUTIONS
K a n d y Power Amplifier 2 Channel
AC MAINS SUPPLY
Your Kandy Power Amplifier is set to operate from a fixed supply voltage which is marked on a label next to the
mains input plug. Before connecting the mains lead please check that your mains supply corresponds to this
label as below:
230V Products ………………………………….Voltage Range: 220V – 240V
115V Products ………………………………….Voltage Range: 100V – 120V
The mains lead supplied with this product has an IEC mains socket that plugs into the IEC connector on the
unit’s rear panel. The other end is normally attached to the appropriate mains plug for your country. In the UK
this is the standard UK13A plug.
This plug should ordinarily not be removed from the lead. If you do remove it, please dispose of it safely so that it
cannot be plugged into a mains socket whilst in a potentially dangerous condition. We suggest that you obtain
from your dealer a complete replacement lead.
Should you move to another area where either the mains voltage or the mains plugs are different from those as
supplied with your Power Amplifier, please contact the appointed ROKSAN distributor for assistance.
Please observe correct mains polarity at all times.
The Kandy Power Amplifier mains fuse is located on the rear panel next to the IEC mains connector. This must
only be replaced by the fuse of the type and rating as described on the fuse rating label on the rear panel of the
unit.
This product requires connection to electrical earth (ground). The earth wire (in the UK this is colour coded
green/yellow) of the mains cable supplied with your Power Amplifier must be connected to a suitable grounding
point established for this purpose by your electricity supply company. If you are in any doubt, consult a qualified
electrician.
If the equipment is likely to be unused for some time, unplug it from the mains supply.
GENERAL CAUTIONS
FCC WARNING
This equipment may generate or use Radio Frequency energy. The user may lose the right to operate this
equipment if unauthorised modifications are made.
INTERFERENCE
Properly installed, this unit should not cause harmful interference to radio communications, There is, however, no
guarantee that such interference will not occur in a specific installation. If interference arises (which you can
determine by switching the unit off and on) you could try to remedy matters by the following:
•
•
•
•
Re-orient or re-locate the receiving antenna
Increase the distance between the Kandy Power Amplifier and receiver
Connect the unit to a different mains circuit from that of the receiver
Consult your ROKSAN appointed dealer or an experienced Radio/TV technician for help and advice
LOCATION
Your Kandy Power Amplifier should be located in a well ventilated area and kept away from sources of heat, dust
and humidity and from direct sunlight.
The Kandy Power Amplifier may be positioned either as a free standing unit or alongside another audio/video
product.
Never place the Power Amplifier on carpet or any surface likely to hinder normal ventilation.
Never allow liquids or other objects to fall into the unit.
This unit contains no user serviceable parts. Do Not remove any panels or attempt to service it yourself.
Unauthorised servicing will void the warranty.
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 3 of 10
ENGLISH
INSTALLATION
K a n d y Power Amplifier 2 Channel
ROKSAN Kandy Power Amplifier- Front Panel View
1
ROKSAN
Power Amplifier KMA-2/3 MkIII
1.
Mode Indicator Light
ROKSAN Kandy Power Amplifier - Rear Panel View
2 3
4
5
1
6
7
8
9
10 11
1.
2.
Right Channel Trimmer
Left Channel Trimmer
3.
4.
5.
6.
Straight/Trimmed Input Selector Switch
Left & Right Channel Trimmed Inputs
Left & Right Channel Straight Inputs
Right Speaker Output
7.
Left Speaker Output
8.
Voltage & Fuse Label
9.
10.
11.
AC Mains Power Switch
AC Mains Input
AC Mains Fuse holder
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 4 of 10
ENGLISH
SET-UP
K a n d y Power Amplifier 2 Channel
CONNECTING MAINS POWER
Please refer to rear panel view on Page 4. The moulded IEC connector of the supplied mains lead should be
plugged into the socket (10) on the rear of the unit first and then plugged into the mains supply. The Mains power
switch (9) is on the rear panel of the Amplifier. This switch is normally left on. If the unit is likely to be unattended
for a long period, switch it off and unplug the mains lead from the wall.
SIGNAL CONNECTIONS
Signal Input Connections:
There are two types of input on the Kandy Power Amplifier, the ‘T’ column of L & R
‘Trim-able’ Inputs (4) and the ‘S’ column of L & R ‘Straight’ Inputs (5).
Input Selector Switch (3) should be set to ‘Straight’ or ‘Trimmed’ according to the inputs that are intended for use.
All the inputs use Gold plated RCA Phono Connectors and should be connected according to the standard
convention –
Right Channel – Red;
Left Channel – Black or White.
Also in accordance with standard practice, the Upper row of Phono Sockets carries the Left Channel and the
Lower row carries the Right Channel.
The Input Sockets are labeled with their legends upside down as well as the normal way up to assist you should
you be connecting an input from a position in front of and above the amplifier.
Straight Input Connections:
First set the Input Selector Switch (3) to ‘STRAIGHT’. If you wish to use the amplifier
for multi-amping with the Kandy Integrated or purely as a power amplifier, you should connect the pre out of your
Kandy Integrated , pre-amplifier or surround sound processor to the corresponding Straight Input. The gain of the
Kandy Power Amplifier is exactly the same as the power amplifier section of the Kandy Integrated Amplifier and
therefore is ideal for Multi-amping (Bi-amping, Tri-amping etc.)
IMPORTANT NOTE: For optimum performance it is recommended to use high quality inter-connect cables
such as ROKSAN HDC-02A high definition analogue Cable.
Trimmed Input Connections:
First set the Input Selector Switch (3) to ‘TRIMMED’. If you wish to use the amplifier
for Multi-channel A/V, directly connected to the Kandy DVD 5.1 Dolby Audio output, or as a power amplifier in
an installation requiring its output level to be trimmed down, then the Trimmed Inputs should be used. (e.g. You
should connect the Kandy DVD audio output to the corresponding Trimmed Input of the Kandy Power Amplifier)
These Inputs can then be fully trimmed down by using the Trimmers (1, 2) on the back
panel.
IMPORTANT NOTE: It is always better to use the Straight Inputs when there are no requirements for level
adjustment.
LOUDSPEAKER CONNECTIONS
The Right and Left loudspeakers are connected to the amplifier via the rear panel binding posts (6) and (7)
respectively. There are two basic types of cable –
•
•
Figure 8 cable has two insulated conductors that lie parallel, either side by side, or spaced by insulation.
Overall sheathed cable has both conductors insulated and enclosed in an overall plastic sheath.
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 5 of 10
ENGLISH
Carefully remove any overall sheath or split the figure 8 cable to a depth of about 75mm (3”).
Carefully strip the insulation on each wire to a depth of about 12mm (1/2”) exposing the
bare core. If the conductor is stranded, twist the strands together on each conductor.
Unscrew the binding post. There is a cross-hole about 5mm from the panel end of the
binding post. Insert the bared conductor through the hole and tighten the binding post
securely making sure that there are no loose strands or bare ends protruding through
the post.
Carefully observe polarity ensuring that the RED (+) speaker terminal is connected to
the RED (+) amplifier terminal and the BLACK (-) speaker terminal to the BLACK (-)
amplifier terminal.
When all the channels are connected to their respective speakers the amplifier is ready
for use.
IMPORTANT NOTE: For optimum performance it is recommended to use high quality cables such as ROKSAN
HDC-02S High Definition Loudspeaker Cable. Many speaker cables such as the ROKSAN HDC-02S are
directional. Please observe this directionality. DO NOT use a speaker cable with conductor size less than 16
AWG (1.6mm Diameter). The Binding posts accept conductor sizes up to 12 AWG.
Multi-Amping The Loudspeakers
Set-up
If the Loudspeakers utilise more than one drive unit with individual input terminals, for example a Tweeter and a
Woofer, then the loudspeaker performance will greatly benefit from Bi-Amping. Dedicating one amplifier to the
Tweeter and another to the Woofer isolates them from each other hence reducing distortion and increasing
reserved power. Speakers work far better with most amplifiers when Multi-Amped than using one yet more
powerful amplifier.
NOTE:
Kandy Integrated Amplifier MkI
& MkII do not have pre out
sockets for multi-amping.
If the loudspeakers have more
drive units you just add more 2-
channel amplifiers and connect
respectively.
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 6 of 10
ENGLISH
Trimmed Input Connection
Set-up
Using the Kandy Integrated Amplifier and Kandy Power Amplifier 2-channel:
CONNECTION NOTES:
1. Connect the Integrated Amplifier L & R Pre outputs to the L & R Trimmed inputs of the 2-channel Power Amp
2. Connect L & R speakers to the 2-Channel Power Amplifier L & R speaker outputs
3. Switch to the ‘TRIMMED’ input on the back
4. Carefully adjust the L & R trimmers to achieve the required level.
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 7 of 10
ENGLISH
OPERATION
K a n d y Power Amplifier 2 Channel
Please refer to the front and rear panel views on page 4.
SWITCHING ON
The Mains power switch (9) is located on the rear panel of the amplifier. This switch should be left ON for normal
operation. If unattended for a long period, the Mains power should be switched OFF and the lead disconnected
from the power supply.
When switched ON from the rear panel, your Kandy Power Amplifier will go to Operational mode and the MODE
indicator light (1) on the front will glow RED. The amplifier is now ready for use.
1
2
3
If there is no signal (or the signal level is very low) the MODE indicator light will change to AMBER after
approximately 2 minutes
If there is still no signal after approximately 15 minutes, the amplifier will revert to Standby mode and the
MODE indicator light will glow GREEN
As soon as there is a signal the Kandy Power Amplifier will ‘wake up’, the MODE indicator light will glow
RED and after a couple of seconds the outputs will be activated.
USING THE TRIMMERS
Please refer to the rear panel views on page 4.
There are two Trimmers (1 & 2), accessible from the back panel, that can be utilised to reduce the input level to
the individual channels and thus reduce the output level. In this configuration the input signal to that channel
must be connected to its Trimmed Input socket only (not the Straight Input) and the selector switch must be set
to Trimmed. When connected as such the gain on that channel can be reduced as indicated below.
NOTE: To avoid damage to the trim pots always use a good quality flat blade electrical trimmer.
Fully Anti-
clockwise
1/8 Turn
clockwise
1/4 Turn
clockwise
3/8 Turn
clockwise
1/2 Turn
clockwise
5/8 Turn
clockwise
Fully
clockwise
Full Gain
31.6 dB
Trimmed
30.4 dB
Trimmed
28.2dB
Trimmed
25.2dB
Trimmed
20.2 dB
Trimmed
12.2 dB
Full Trim
Full Mute
NOTE: These values and positions are approximate and should be used as a guide. During the installation and
set-up, you should adjust the trimmer to achieve the desired output level.
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 8 of 10
ENGLISH
TROUBLESHOOTING
K a n d y Power Amplifier 2 Channel
If you suspect that your ROKSAN Kandy Power Amplifier is not operating properly, you should check all the
connections carefully. Pay particular attention to speaker phasing and channel connections. Phono plugs should
be fully inserted- a frequent cause of problems is that Phono plug surrounds do not make proper contact. Below
are some commonly encountered problems with suggestions for possible cure. The list is not exhaustive: If you
have any unresolved problems, please consult your appointed ROKSAN dealer or distributor.
SYMPTOM
LIKELY CAUSE
SUGGESTED REMEDY
No power
AC Mains lead not inserted properly
Unit not switched on at rear panel
Missing or bad input signal connection
Incorrect speaker connection
Ensure AC Mains lead is fully inserted
Switch unit on at rear panel
Check all input connections
Check speaker output connections on
rear panel
No output on one or more
channels
Lower output on one or both Higher trim on one or both channels
channels
Check trim level and adjust accordingly
Poor speaker imaging, lack
of Bass output
Loudspeakers connected out of phase
Check polarity of speaker connections
(especially important if Multi-wiring,
Multi-amping)
Hum from speakers
Incorrect Grounding
Check Mains polarity and grounding on
all connected equipment
GUARANTEE
K a n d y Power Amplifier 2 Channel
There are no user-serviceable parts inside your Kandy Power Amplifier. If a fault should develop, refer any
servicing to your appointed ROKSAN dealer, distributor or ROKSAN approved service agent.
Your ROKSAN Kandy Power Amplifier is guaranteed against any defect in materials and workmanship for a
period of two years from the date of purchase.
This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the
equipment was purchased and returned to ROKSAN within 28 days of purchase.
This guarantee excludes:
1. Damage caused due to accident, missuse, neglect and incorrect installation, adjustment or repair.
2. Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised
distributor for the purposes of repair or inspection.
Carriage costs to ROKSAN shall be borne by the consignor.
All claims under this guarantee must be made through an authorised ROKSAN retailer.
If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification
ROKSAN reserves the right to make a charge for examination and return carriage.
Unauthorised servicing will void this guarantee.
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 9 of 10
ENGLISH
SPECIFICATIONS
K a n d y Power Amplifier 2 Channel
Inputs
Straight (x2)
Trimmed (x2)
Input Impedance
Input Sensitivity (115W)
Outputs
10 kΩ
900mV
Speaker L & R (x1)
Output Power
>120 Watts, into 8Ω
both channels driven
>185 Watts, into 4Ω
both channels driven
Power Supply
500VA Ultra Low Noise Toroidal Transformer
Damping Factor
Frequency response
>110 (8Ω)
(-3dB), <3Hz – >100kHz
Straight or trimmed input
Gain
31.6 dB Straight or untrimmed
-50 dB (Full Mute) Fully trimmed
Harmonic Distortion
Signal to Noise Ratio
Power Source
<0.005% 1kHz - 8Ω
100dBa (ref. 900mV)
100V – 120V 50Hz / 60Hz
220V – 240V 50Hz / 60Hz
Power Consumption
Dimension
Standby <25W, Full Power <800W
432 x 380 x 90 (W x D x H) mm
432 x 380 x 105 (including feet)
Weight
14 Kg
NOTES
K a n d y Power Amplifier 2 Channel
Kandy Power Amplifier L.III
Serial Number: …………………………
Year .……… Month …….. Day ……..
Purchase Date
ROKSAN Retailer
Name:
…………………………………
Location: ………………………………
Please keep a record for future reference
Roksan Audio ltd
Kandy Power Amplifier 2-Channel User Manual
CLASSIFICATION: General Use
Version 1.01
All specifications are liable to change without notice. E&OE
Page 10 of 10
ENGLISH
|